Entegre

To increase the adherence: In Gypsum based Plasters, use "Primel 600" for the gross concrete surfaces in the internal spaces.
To minimize the scratches: Use nets on the concrete-wall connections.
To provide homogeneity: In Cement based plasters, don’t make extra trifle on the final surface. After trifle, apply sponge trifle procedure.
In the plasters applied manually, strictly comply with the water proportions.
Homogenous mixture: In machine applied plasters, keep the water proportion constant.
In the plasters, don’t make applications under +5 C and over + 35 C.
To increase the adherence capability of the material: In the plasters, apply maximum 2.5 cm thickness in a single layer.
To increase the adherence: In Gypsum based plasters, apply maximum 2.5 cm, if more is required, apply the 2nd coat before the 1st coat settles.
To increase the adherence: In Cement based plasters, apply maximum 2.5 cm in a single layer, if more is required, apply the second coat the next day.
Don’t add additives such as sand, cement, gypsum plaster etc. to the plasters.
To prevent scratches: In Cement based plasters, don’t apply early smoothing.
To increase the adherence: In plasters, clean and moisten the surface before application.
To prevent scratches and increase resistance: In the plasters, apply curing after plaster in compliance with the seasonal conditions.
To provide homogeneity: “Mix Eltek SD” with an electrical hand mixer.
To prevent scratches early water loss: On facades exposed to excess wind, protect the plaster against rapid drying.
In cement based plasters, apply paint application 28 days after, according to the seasonal conditions.
In gypsum plaster based plasters, apply paint application 10 days after, according to the seasonal conditions.
In cement based plasters, place maximum 8 bags on top of each other in order to prevent squeezing.
The net life of Cement based plaster in a non-humid environment is 6 months. Don’t forget that the material would petrify otherwise.
On the facades that face north, and receive excess rain, use water resistant plaster.
To increase the adherence: On gross concrete surfaces, mix “Primel Powder” and “Primel 200” at appropriate proportions (1/3) and use this before the Cement based plaster applications on the internal and external facades.
On Gas-Concrete surfaces make direct application in gypsum plaster-based plasters without using “Primel”.
On Gas-Concrete surfaces, apply powder “Primel” before applying cement-based plasters. Start application by curing after 72 hours.
In order to prevent color tone changes: In “Colormatik” applications, keep the application thickness and machine water level constant.
In Gypsum based plasters, pre-application of “Alçımatik” should be min 8 mm; and “Satenmatik” application should be min 3 mm max 8 mm.
To prevent squeezing: In Gypsum based plasters place maximum 8 bags on top of each other.
In Gypsum based plasters, don’t forget that the shelf life is max 3 months.
In Gypsum based plasters, don’t forget to clean the reinforcing bars in the columns, beams and the ceiling with anti-rust paint.
Use “Sapser Rapid” in rapid ground applications.

To provide resistance against water, frost: Use “Doltek” and “Dolfin” in place of “Dolel” on the external facades.
To increase the adherence: In special products, clean and moisten the application surface before the application.
To provide homogeneity: Prefer mixing the special products by electrical hand mixer.
Strictly don’t add additives such as lime, sand, cement etc. in the mortar prepared.
Make sure that the application temperature is between +5 C to +35 C interval.
To prevent scratches and increase resistance: Apply curing after the application in compliance with the seasonal conditions.
To save time: Use “Rapidfix” that sets quickly in rapid applied repair mortars.
Don’t apply special products on Gypsum based plaster.
Try to apply the water proportion specified in the technical specifications of the special products.
Read the technical catalogue well for the special products. Don’t use the wrong product in a wrong place.

To provide homogeneity: First put the water in the mixing container and mix it by the electrical mixer.
Don’t add additives such as lime, sand, cement etc. in the mortar.
Make sure that the application temperature is between +5 C to +35 C interval.
Read the technical catalogue well for the adhesives. Use the correct adhesive in the correct place.
Use Flex products on the floors that are heated from below.
Don’t apply ceramic adhesive on settled surfaces.
Wait 24 hours for jointing applications.
Use Karofix Rapid in order to save time in rapid ceramic covering applications.
In ceramic on top of ceramic applications, it is required to be sure of the soundness of the old ceramic covered surface. After making a soundness check, Entegre Karofix Super provides a perfect performance with double-side application.
To increase the adherence: Clean and moisten the surface before the application.
Use Camserfix in glass bricks and jointing.
Use Mozafix in mosaic applications and jointing. Perform the jointing after 24 hours.
Make sure that appropriate joint gaps are provided before jointing, provide that joint mortar penetrates in between the ceramics in the most convenient way.
If the joint gaps are full, clean them with a brush before the application.
Use Flex joint filling in places which require high performance.
In wet spaces, for 100% water insulation before ceramic applications, apply Entegre Sutop Double flexible water insulation product two coats as horizontal and vertical layers.
Make sure that you apply joint filling mortar in compliance with the water proportion specified in the technical documentation.

Tips

PLASTERS

SPECIAL PRODUCTS

ADHESIVES AND joinTING MORTARS